0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |     Code      |          Checksum             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             MTU                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    As much of invoking packet                 |
      +               as will fit without the ICMPv6 packet           +
      |               exceeding the minimum IPv6 MTU [IPv6]           |

   IPv6 Fields:

   Destination Address

                  Copied from the Source Address field of the invoking
                  packet.

   ICMPv6 Fields:

   Type           2

   Code           Set to 0 (zero) by the sender and ignored by the
                  receiver

   MTU            The Maximum Transmission Unit of the next-hop link.

  Description

   A Packet Too Big MUST be sent by a router in response to a packet
   that it cannot forward because the packet is larger than the MTU of
   the outgoing link.  The information in this message is used as part
   of the Path MTU Discovery process [PMTU].

   Sending a Packet Too Big Message makes an exception to one of the
   rules of when to send an ICMPv6 error message, in that unlike other
   messages, it is sent in response to a packet received with an IPv6
   multicast destination address, or a link-layer multicast or link-
   layer broadcast address.

   Upper layer notification

   An incoming Packet Too Big message MUST be passed to the upper-layer
   process.






 
RFC 2463                 ICMPv6 (ICMP for IPv6)            December 1998


3.3 Time Exceeded Message

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |     Code      |          Checksum             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             Unused                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    As much of invoking packet                 |
      +               as will fit without the ICMPv6 packet           +
      |               exceeding the minimum IPv6 MTU [IPv6]           |

   IPv6 Fields:

   Destination Address
                  Copied from the Source Address field of the invoking
                  packet.

   ICMPv6 Fields:

   Type           3

   Code           0 - hop limit exceeded in transit

                  1 - fragment reassembly time exceeded

   Unused         This field is unused for all code values.
                  It must be initialized to zero by the sender
                  and ignored by the receiver.

   Description

   If a router receives a packet with a Hop Limit of zero, or a router
   decrements a packet's Hop Limit to zero, it MUST discard the packet
   and send an ICMPv6 Time Exceeded message with Code 0 to the source of
   the packet.  This indicates either a routing loop or too small an
   initial Hop Limit value.

   The rules for selecting the Source Address of this message are
   defined in section 2.2.

   Upper layer notification

   An incoming Time Exceeded message MUST be passed to the upper-layer
   process.