$(top_srcdir)/configure:  $(am__configure_deps)
	cd $(srcdir) && $(AUTOCONF)
$(ACLOCAL_M4):  $(am__aclocal_m4_deps)
	cd $(srcdir) && $(ACLOCAL) $(ACLOCAL_AMFLAGS)

config.h: stamp-h1
	@if test ! -f $@; then \
	  rm -f stamp-h1; \
	  $(MAKE) stamp-h1; \
	else :; fi

stamp-h1: $(srcdir)/config.h.in $(top_builddir)/config.status
	@rm -f stamp-h1
	cd $(top_builddir) && $(SHELL) ./config.status config.h
$(srcdir)/config.h.in:  $(am__configure_deps) 
	cd $(top_srcdir) && $(AUTOHEADER)
	rm -f stamp-h1
	touch $@

distclean-hdr:
	-rm -f config.h stamp-h1
command.cfg: $(top_builddir)/config.status $(srcdir)/command.cfg.in
	cd $(top_builddir) && $(SHELL) ./config.status $@
test.pl: $(top_builddir)/config.status $(srcdir)/test.pl.in
	cd $(top_builddir) && $(SHELL) ./config.status $@
pkg/solaris/pkginfo: $(top_builddir)/config.status $(top_srcdir)/pkg/solaris/pkginfo.in
	cd $(top_builddir) && $(SHELL) ./config.status $@

mostlyclean-libtool:
	-rm -f *.lo

clean-libtool:
	-rm -rf .libs _libs

distclean-libtool:
	-rm -f libtool
uninstall-info-am:

# This directory's subdirectories are mostly independent; you can cd
# into them and run `make' without going through this Makefile.
# To change the values of `make' variables: instead of editing Makefiles,
# (1) if the variable is set in `config.status', edit `config.status'
#     (which will cause the Makefiles to be regenerated when you run `make');
# (2) otherwise, pass the desired values on the `make' command line.
$(RECURSIVE_TARGETS):
	@failcom='exit 1'; \
	for f in x $$MAKEFLAGS; do \
	  case $$f in \
	    *=* | --[!k]*);; \
	    *k*) failcom='fail=yes';; \
	  esac; \
	done; \
	dot_seen=no; \
	target=`echo $@ | sed s/-recursive//`; \
	list='$(SUBDIRS)'; for subdir in $$list; do \
	  echo "Making $$target in $$subdir"; \
	  if test "$$subdir" = "."; then \
	    dot_seen=yes; \
	    local_target="$$target-am"; \
	  else \
	    local_target="$$target"; \
	  fi; \
	  (cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
	  || eval $$failcom; \
	done; \
	if test "$$dot_seen" = "no"; then \
	  $(MAKE) $(AM_MAKEFLAGS) "$$target-am" || exit 1; \
	fi; test -z "$$fail"

mostlyclean-recursive clean-recursive distclean-recursive \
maintainer-clean-recursive:
	@failcom='exit 1'; \
	for f in x $$MAKEFLAGS; do \
	  case $$f in \
	    *=* | --[!k]*);; \
	    *k*) failcom='fail=yes';; \
	  esac; \
	done; \
	dot_seen=no; \
	case "$@" in \
	  distclean-* | maintainer-clean-*) list='$(DIST_SUBDIRS)' ;; \
	  *) list='$(SUBDIRS)' ;; \
	esac; \
	rev=''; for subdir in $$list; do \
	  if test "$$subdir" = "."; then :; else \
	    rev="$$subdir $$rev"; \
	  fi; \
	done; \
	rev="$$rev ."; \
	target=`echo $@ | sed s/-recursive//`; \
	for subdir in $$rev; do \
	  echo "Making $$target in $$subdir"; \
	  if test "$$subdir" = "."; then \
	    local_target="$$target-am"; \
	  else \
	    local_target="$$target"; \
	  fi; \
	  (cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
	  || eval $$failcom; \
	done && test -z "$$fail"